Assistant Tool1
SKU:
$35.00
$35.00
Unavailable
per item
Usage
• 150 mm extension @ Without Spindle Size
• Excellent for sanding inside of plates and pockets
• Two type of sanding : Sand paper, Flap paper
• Need to use “Speed Regulator to lower voltage” for sanding
Angle grinder is not included
Please check your "Spindle size" of angle grinder.
• 150 mm extension @ Without Spindle Size
• Excellent for sanding inside of plates and pockets
• Two type of sanding : Sand paper, Flap paper
• Need to use “Speed Regulator to lower voltage” for sanding
Angle grinder is not included
Please check your "Spindle size" of angle grinder.
Recommended Item
Check your Spindle Size
Angle grinder is not included.
Please check your "Spindle size" of angle grinder.
M10 : Aisa
M14 : EU
5/8"-11 : U.S.A, CANADA
Demonstration Image
Usage and Safety Precautions
- Please read and follow all safety instructions carefully. Please keep the manual for future reference.
- When operation, always wear safety equipment such as face masks and safety goggle.
- Always secure the workpiece securely when working.
- Make sure that the grinder switch is off before plugging in the power cord.
- Be careful not to touch the cutter blade. Serious injury may result.
- Always operate the tool with both hands firmly gripped, and never leave the tool with rotation.
- When using the tool, always use 220V without speed adjustment so that the speed does not fall below 11000RPM.
- After operation, turn off the switch and set it down when The remaining rotation stop completely.
- Please be sure to use it carefully because it may cause the rotation reaction(kick back) depending on the direction of rotation.
- Please remove the stone, sand and other material beforehand to use. If not, you may get blades damage.
- Please read and follow all safety instructions carefully. Please keep the manual for future reference.
- When operation, always wear safety equipment such as face masks and safety goggle.
- Always secure the workpiece securely when working.
- Make sure that the grinder switch is off before plugging in the power cord.
- Be careful not to touch the cutter blade. Serious injury may result.
- Always operate the tool with both hands firmly gripped, and never leave the tool with rotation.
- When using the tool, always use 220V without speed adjustment so that the speed does not fall below 11000RPM.
- After operation, turn off the switch and set it down when The remaining rotation stop completely.
- Please be sure to use it carefully because it may cause the rotation reaction(kick back) depending on the direction of rotation.
- Please remove the stone, sand and other material beforehand to use. If not, you may get blades damage.
Maintenance and inspection
- Inspect and tighten the bolts of each part before operation.
- After working, please keep clean so that there is no foreign matter such as dust, sawdust and rosin.
- If the cutter blade or belt is worn out, replace it with a new one.
- Inspect and tighten the bolts of each part before operation.
- After working, please keep clean so that there is no foreign matter such as dust, sawdust and rosin.
- If the cutter blade or belt is worn out, replace it with a new one.
Quality display
- Manufacturer : MANPA corporation.
- Country of manufacture : Made in republic of korea.
- Address : Manpa corporation, 700-20 manseo-ro, Yangseong-myeon, Anseong-si, Gyeonggi-do
- Phone number : 010-8777-5735 / (031)-676-9212
- Web site. : http://www.manpa21.com
- Manufacturer : MANPA corporation.
- Country of manufacture : Made in republic of korea.
- Address : Manpa corporation, 700-20 manseo-ro, Yangseong-myeon, Anseong-si, Gyeonggi-do
- Phone number : 010-8777-5735 / (031)-676-9212
- Web site. : http://www.manpa21.com